✔ IoT and Wireless Monitoring

What are LoRa and LoRaWAN? Long-range monitoring with very low power

LoRa (Long Range) is a radio technology that sends small data packets over long distances with very low power.

LoRaWAN is the network protocol running on LoRa; it defines how devices connect to a network server through gateways. It is used to monitor large areas without cabling, with sensors that can run on batteries for years.

Highlights

  • 868 MHz (Turkey/Europe)
  • Licence-free band
  • Years on battery
  • Kilometres of range
  • To SCADA via MQTT

How does it work?

A sensor broadcasts its measurement by radio. One or more nearby gateways receive it and forward it over the internet or local network to the network server. The network server decodes the data and usually passes it to SCADA or an application via MQTT.

Sensors spend most of their time asleep and wake up only to send data, which is why battery life is long. Sensors far from the gateway use a slower but longer-reaching setting; this affects battery use and transmission time.

Hardware architecture

LoRa Sensorsbattery poweredLoRaWAN Gatewayon a roof or high pointEthernet / 4GbackboneNetwork Servere.g. ChirpStack, TTNMQTT → SCADAmonitoring and alarms
  • Sensors (end nodes): Ready-made sensors for temperature, humidity, meters, level, doors and leaks, or converters that connect Modbus devices to LoRa.
  • Gateway: Placed at the highest possible point (roof, mast). Outdoor (IP67) models with external antennas are preferred.
  • Network server: Can run on your own server (e.g. open-source ChirpStack) or as a service. Your own server keeps control of the data with you.
  • Gateway connection: Ethernet is the most reliable; 4G is used at remote sites.

Cable and material selection

  • Antenna: Use an outdoor antenna suited to the 868 MHz band. Mount it high with no obstacles around it; antenna height affects range more than anything else.
  • Antenna cable: Choose low-loss coaxial cable and keep it as short as possible. A long, thin cable throws away the range you gained.
  • Lightning protection: Fit a coaxial surge protector on the antenna line and ground it.
  • Gateway power: With PoE (Power over Ethernet), one cable carries both data and power, which simplifies rooftop installs.
  • Sensor placement: Metal cabinets and concrete basements weaken the signal; move the sensor or its antenna to an open spot where possible.
  • Batteries: Use lithium batteries rated for cold environments; low temperatures shorten battery life.

Advantages of monitoring with LoRa

  • Wireless installation: No cable trays or digging; installation is faster.
  • Long battery life: Sensors that send data infrequently can run on batteries for years.
  • Wide coverage: A single gateway can cover a large factory site, campus, industrial zone or farmland. Range can reach several kilometres in open areas and a few kilometres in cities.
  • Low running cost: With your own gateway, there is no per-sensor line fee.
  • Hard-to-reach points: Meters and sensors in basements, wells, warehouses and scattered locations can be monitored.

Advantages and disadvantages

Advantages

  • Very low power, years on battery
  • Long range, wide area with few gateways
  • Licence-free frequency, no mandatory line fees
  • Easy to add to an existing SCADA via MQTT
  • Good penetration indoors and at hard-to-reach points

Disadvantages

  • Low data rate; only suitable for small, infrequent data
  • Legal duty cycle limits restrict how often data can be sent
  • Not suitable for real-time monitoring and control
  • Latency and packet loss can occur; do not use for critical control
  • Coverage depends on site survey and antenna placement

LoRa compared with similar technologies

LoRaWANNB-IoTWi-Fi4G
RangeLong (km)Network coverageShortNetwork coverage
Battery lifeVery longLongShortShort
Data volumeVery lowLowHighHigh
InfrastructureYour own gatewayOperatorYour own access pointOperator
Line feeNoneYesNoneYes
Best forWide area, infrequent dataUrban metersIndoorsRemote sites, high data

How to test it

  1. Install the gateway and check that it shows as online on the network server.
  2. Register the sensor on the network server and see the first data arrive near the gateway.
  3. Move the sensor to its real location and check signal strength (RSSI) and signal quality (SNR).
  4. Subscribe to the network server's MQTT output with mosquitto_sub or MQTT Explorer and watch the data arrive.
  5. Track packet loss over a few days.

Testing with ATLAS SCADA

You can test LoRa data coming from the network server via MQTT with ATLAS SCADA: link the topics to tags, watch sensor values on the SCADA screen and define alarms.

Let's review your project together

Let's work out together which architecture, hardware and cabling fit your facility.

Let's talk about your project